[email protected]

17-4 PH Stainless Steel supplied in Sheet, Plate, and

17-4 PH steel is a grade of martensitic, precipitation-hardening stainless steel with the additions of chromium, nickel, and copper. Type 17-4 PH (AMS 5604) is the most widely used of all precipitation-hardening steels, and we are suppliers of 17-4 PH sheet, coil, and 17-4 PH round bar and plate. ALLOY DATA / 17 - ASM International the Materials Aluminum magnesium alloy; Cr 0.25; Mg 2.5; bal Al. O-temper:193 MPa TS; 90 MPa YS; 25 El; 47 HB; H38-temper:290 MPa TS; 255 MPa YS; 7 El; 77 HB; Sheet metal work, marine applications. A 5056 Comalco Ltd. Aluminum magnesium alloy; Cr 0.1; Mg 5.2; Mn 0.1; bal Al. O-temper:290 MPa TS; 152 MPa YS; 35 El; 70 Vickers. H38-temper:414 MPa TS; 345

ASTM A513 Tubing - Valmont Tubing

Produced in sizes ranging from 1.05" OD up to 12.75" OD and in nominal wall thicknesses beginning at 18-gauge (0.049") and heavier, Valmont's ASTM A513 tubing is used in a variety of industrial, agricultural and transportation-related end uses. For a complete listing of sizes produced, please visit our Steel Tubing Product Catalog. Alloy 17-4PH Material Datasheet17-4 PH Steel contains 4% copper and may be hardened by a single low temperature precipitation hardening heat treatment, producing excellent mechanical properties at a high strength level. 17-4 PH provides this high strength in combination with good mechanical properties at temperatures of up to 600°F (316°C). It exhibits good toughness in both base metal and welds and has an excellent Cross Reference of ASTM Material SpecificationsA ASTM cross reference material specification of fittings, flanges, unions and cast and forged valves:Materials. Forgings. Castings. Wrought Fittings. Pipe. Carbon

Equivalents of Carbon Steel Qualities

Equivalents of Carbon Steel Qualities. Boiler steel. Fine-grain structural steels, normalised rolled. Fine-grain structural steels, thermomechanically rolled. General Construction Steel. General purpose structural steels. High carbon steels. High strength steels for cold-forming, normalised. Materials - Chemical Composition (Requirements) for Carbon The sum of Copper, Nickel, Niobium, Molybdenum and Vanadium shall not exceed 1.00%. The sum of Niobium and Molybdenum shall not exceed 0.32%. Note:For each reduction of 0.01% below the specified carbon maximum (0.35%), an increase of 0.06% Manganese above the specified maximum (1.05%) will be permitted up to a maximum of 1.35%. Materials Science and Engineering:A Journal Materials Science and Engineering A provides an international medium for the publication of theoretical and experimental studies related to the load-bearing capacity Effect of B 4 C particles addition on microstructure and mechanical properties of Fe 50 Mn 30 Co 10 Cr 10 high-entropy alloy. Lin Deng, Li-peng Ding. In Press, Journal Pre

SAE steel grades - Wikipedia, the free encyclopedia

Jul 10, 2012 · ISO 3506.[6] 316Ti includes titanium for heat resistance, therefore it is used in flexible chimney liners. Type 321similar to 304 but lower risk of weld decay due to addition of titanium. See also 347 with addition of niobium for desensitization during welding. SAE steel grades - qtstoolsDuctile iron. Gray iron. Malleable iron. White iron. Wrought iron (contains slag) The Society of Automotive Engineers (SAE) designates SAE steel grades. These are four digit numbers which represent chemical composition standards for steel specifications. The American Iron and Steel Institute (AISI) originally started a very similar system. SUBSTITUTE MATERIAL (JIS, BS, DIN ) FOR ASTM 5. Table 1, Plates 6. Table 2, Pipes 7. Table 3, Tubes 8. Table 4, Forging 9. Table 5, Castings 10. Table 6, Bolts and Nuts 11. Table 7, Bars and Shapes 12 Table 8, Piping Fittings 13. Table 9, Nonferrous Materials 1. SCOPE

Chemical Composition - Steelmetal

Specification Grade C % max Mn % max P % max S % max Si % SAIL-FRS 0.20 1.5 0.040 0.040 Cr+Mo Nb+V+Ti %=1.00 (max)% 0.12 Note:Micro alloying elements like Nb, V, Ti or B shall be added singly or in combination and total micro alloying shall be as indicated